Preparing for installation

• Read the user manuals for the sauna materials and the installation guides for all electrical devices to be used
• Check that there is adequate ventilation in the room where the sauna is to be installed
• Make sure that the wooden materials won’t come into constant contact with water, for instance at the bottom of the wall, during installation
• Ensure that the external surfaces of the sauna won’t remain exposed to water or moisture upon installation
• Ensure that any electrical work, including installation of the electric sauna heater, is done by a licensed electrician

Treating wooden components

• It is obligatory to treat the wooden parts with special liquids to protect the wood from moisture. Treatment liquids are available in well-equipped construction stores. The manufacturer is not responsible for the products which are damaged due to the lack of protective treatment or incorrect installation.
• Dust all of the wooden sauna components and then clean them with a sauna detergent before allowing them to dry
• Treat the walls and ceilings on both sides with a specialist sauna finish product such as Tikkurila Supi Saunasuoja and then treat all surfaces of the seating materials with a sauna bench protection product like Tikkurila Supi Laudesuoja
• Don’t use paints or varnishes, as the wood must be able to breathe

Installing the heater and heating stones

• Ensure that the heater is installed according to the manufacturer’s instructions
• Install the heating stones as directed by the manufacturer and make certain that the heating elements aren’t visible, as pouring water directly onto them can reduce their lifespan
• Wash the heating stones to remove any production chemicals
• Important – do not use your sauna when heating it for the first time!
• During the first heating, do so under supervision to a temperature of about 100°C for two hours, keeping the sauna well ventilated both during and after heating; the heat will cause the wood to absorb the treatment products, which will form a protective layer

During use

• Only throw water on the heater, not on the walls or benches
• Don’t wear wet swimsuits in the sauna, as water from these will damage the bench
• To keep the bench fresh, we recommend using seat covers – these can also make it more comfortable to sit on the bench when it is hot
• Keep an eye on the heating stones, as they may crack over time – whenever necessary, they can be replaced or
  more stones can be added

After each use

• Wipe the benches with a clean, damp cloth – don’t use running water to clean them, and ensure that excess water doesn’t pool on the wooden surfaces
• Use appropriate cleaning products for the benches and other wooden components, reading the instructions first
• After cleaning your sauna, allow the surfaces to dry and ensure that the room is well ventilated – we recommend leaving the heater on for at least half an hour with the air vent open and the door and windows closed
• If possible, lift up the benches to allow them to dry better

At least once per year

• Treat the sauna’s wooden surfaces with an appropriate product (see Treating wooden components above) – this should be done more frequently if the sauna receives intensive use
• Clean all surfaces of the seating materials, walls, and ceilings using a soft brush or cloth and a specialist cleaning product, following the instructions on the packaging
• For deeper stains and soiling, gently clean the bench using a fine sandpaper before treating the sanded surface with a wood preservative (see Treating wooden components)
• Avoid using cleaning agents that are unsuitable for saunas – for example, disinfectants bleach the wood and can spoil its surface
• Inspect the fastenings on the benches and supports, tightening any screws if necessary; they may loosen over time due to changes in the wood caused by heat and humidity

Things to avoid

• Don’t dry textiles in your sauna, as this can be a fire hazard – excessive moisture can also damage the surface of the wood
• Avoid heating the sauna beyond the maximum temperature specified by the heater manufacturer – excessive heat may create a fire risk or cause the wood to warp
• Never use a pressure washer or running water when cleaning your sauna, as excessive moisture can permanently damage the structure and surface of the wood

How wood changes when used in the sauna

• Wood is a natural material, and its surface may crack or bend when used in the sauna
• This is normal due to the extreme and rapid changes in temperature and humidity that occur
• The risk of wood deformation depends on the material and intensity of use – the effects are also more visible in wider boards
• Wooden materials in the part of the sauna most exposed to the hot steam may darken over time
• When new, thermally modified wood may give off a noticeable scent as the sauna is heated, but this will diminish over time

Thermory’s range of wooden sauna products includes a large selection of thermally modified products. Of these, the most exclusive and luxurious items are made with wood that has undergone intense thermal modification, which gives it a beautiful rich brown color, such as dark alder and radiata pine. These elegant materials can be sensitive, and they require special care and attention to maintain their appealing properties.

• Handle packs of wood or individual boards with care during installation
• Don’t scratch the surface of the wood or slide the boards over one another
• Thermally modified wood has a distinctive scent that diminishes over time but never fully vanishes – however, it will lose this scent more quickly if the sauna is heated for an extended period while being ventilated
• Treating the wood with a suitable wood oil or care product will also soften the scent
• Avoid washing untreated thermally modified wood with water, as this will intensify the scent
• Please note that we cannot accept claims about the quality or scent of the wood after it has been cut, installed, or treated